Carbon Costume

…two-tone jacket, and a cross-body bad and your cosplay is ready to go….

…The Hunter is the player character and main protagonist of From Software’s action horror RPG Bloodborne. The player guides him or her through a nightmarish world infested with the Old Blood to reach their destiny of achieving “Paleblood”. Along the way, the player will discover the true horror of their world and surroundings. The Hunter can be either male or female and the clothes remain the same. Capelet and blunderbus optional….

…sister. He quickly takes a place on Team Flash and becomes Kid Flash as well as The Flash in certain timelines. When he isn’t saving the world as a speedster he spends his time drag racing and trying to find where he fits in the wider world. He tends to prefer comfortable clothes like jeans, flannel button ups, and t-shirts as well as shoes he can easily drive in. And while his Flash costume is usually yellow, he has been known to wear the iconic…

…Ichabod Crane has been resurrected to fight not only the Headless Horseman, but also the messengers of the end of the world. Teaming up with a modern day police lieutenant, Ichabod has adapted surprisingly well to the 21st Century. By serving as police consultant, he hopes to save Sleepy Hollow, the world, and his beloved departed wife from the apocalypse….

…ro of Light and the leader of their group, though that is only once they fall into the dark world. Before that, though, Kris is a kind but quiet person that some mistake for awkward or creepy. That does not stop Kris from standing by their friends, though! There are two costumes you can use if you want to dress as Kris. The first is a pair of black jeans and black high tops with a green pullover. In this form, Kris’ hair is a dark brown. In the da…

…ne thin layer of wood glue to fill in gaps on worbla. You can use a paint brush, I just use my hands. Allow to dry. Take your flat white spray, and spray your cones with white spray paint. Allow to dry. Spray with white Plastidip, applying coats as needed, allowing for drying time in between coats. Take your skewered ends, and poke them into your black foam discs. Once you’ve created your holes, remove skewer, add a small bead of wood glue to adhe…

…First Blade, a bone knife Dean wields at some point in the series’ lengthy run, using basic materials you can probably find around your house. (I did, after all, spring this convention trip on my friend rather quickly, so it was definitely a con-crunch type of project!) Materials needed: Hot glue gun Lots of hot glue sticks (you’ll want to stock up) Flexible wire hanger Scotch tape Gray and tan acrylic paint (optional) Black string Styrofoam Tooth…

…ptional) Fine grit (180 or above) Sandpaper Hot glue gun Cheap foam paint brushes (for applying Mod Podge) Measure the widest part of your forearm, then measure from your wrist upward to determine how high you would like your gloves to go. To allow for movement room, add 1/2”-1” to the width of your forearm. Take these measurements, mark them with your pencil carefully, and cut 2 rectangles out of your 3/8” EVA foam using your X-acto knife. Using…

…rs, dyes, etc. I didn’t want you to have to buy a bunch of fancy products just to use on one project. If you feel like you’d rather choose a different method, go for it! Think of places where dirt would hit more. The bottoms, sleeves, arm bands, etc. These places would be dirtier than the rest of the costume. Tea Bath Boil a large pot of water, and add tea bags. I used about 8. Let steep for 4-5 minutes, then turn heat off. Wrap your arm bands tog…

…0 glue 14. Twine (1 spool) 15. White 3mm craft foam (2 sheets) 16. A paintbrush or foam brush 17. X-acto knife 18. Sewing scissors 19. White thread (1 spool) 20. Blue thread 21. Pearl flat back cabochons (1 large, 2 small) 22. Elastic (1 pack) 23. Earring hooks (1 pair) 24. A Sharpie 25. A large circular cookie cutter 26. White embroidery thread (at least one skein) 27. Large sheet of tan or sandstone felt (at least 4 pieces) 28. Fabric glue STEP…